Tag Archives: repairing a washing machine

How to Drain a Washing Machine for Moving

You are excited. You have found a new job in a different state or you built your house and you have to move from your current rental apartment. Among the things you have to move with is the washing machine.

Unfortunately, you can’t carry it with water—you have to drain the water. Since you don’t want to have any water remaining behind that might damage your other valuables, you have to properly drain the washing machine.

How do you do this?

Here is a guide given by washer repair experts on how to drain a washing machine for moving:

Step 1: Disconnect the machine from the power

Start with switching off the power button on the machine and unplug the machine from the power source. To avoid splashing the power cord with water, duct tape it to the top of the washing machine.

Step 2: Locate the drain hose and water supply hoses

If necessary, pull the washing machine away from the wall and access the drain hose. The drain hose is often located at the back of the washer, along with hot and cold water supply hoses. And it carries wastewater away from the machine while the hot and cold water supply hoses bring clean water to the machine.

To tell them apart, the hot hose is colour-coded red while the cold one is coded blue. The drain hose is often gray.

Step 3: Drain the washing machine

Depending on how the washing machine is installed, the drain hose might be carrying water into a standpipe, a drainpipe in the wall, or a large nearby utility sink.

To drain the washing machine, place a large bucket in place and disconnect the drain hose from the pipe by simply wigging it loose. You should then hold the hose up in the air to prevent water from flowing out until you place the bucket in place.

Once the bucket is in place, lower the end of the hose below the water level and gravity will cause the water to flow out.

If the water is too much that you have to pause to empty the bucket, simply place the disconnected end of the drain hose.

Step 4: Get rid of the drain hose blockage

If you find that the water doesn’t flow out or it drains too slowly, chances are you have a blockage in the drain hose. To unclog the drain hose, release the clog using a plumber’s snake. To do it, push the tip of the coil until it reaches a blockage, then turn it manually with the handles on the opposite end until you get through the blockage.

Step 5: Remove the clog in the drain pump

If the clog isn’t in the drain hose, chances are it’s in the drain pump. Depending on your machine, the drain pump might be located behind the removable panels in the front or back of the washing machine. It’s also not uncommon to find it at the bottom of the machine, and you have to tip the machine forward to access it.

After locating the pump, remove the spring clamps by squeezing them with a pair of pliers and clear any clogs present using needle-nosed pliers. The clogging material can range from small articles of clothing to a buildup of lint or pet hair.

Once you are done, reattach the hoses.

Step 6: Inspect the machine

You are better off fixing the washing machine before you move so that when you get to your new home, you will have time to enjoy it, not start looking for an appliance repair Fairfax to fix the machine.

Inspect the washing machine’s lid switch and confirm its working properly. All you need to do is to depress the lid switch by hand and if you don’t hear a click, its most likely broken and needs replacement.

You also should take a look at the belts and if they are damaged, unscrew the access pane and replace them.

You can do the work by yourself, but if the work is above your skill level, let a professional handle it. For best results, ensure the professional is experienced and certified to work in your local area.

Is It Worth Repairing a 15-Year-Old Washing Machine?

Are you wondering, is it worth repairing a 15-year-old washing machine? Well, this depends on the broken part and the cost of repairing it. If the broken part is easy to find, so you can easily source it and not expensive to repair, it’s worth repairing the appliance, but if the part is hard to find and expensive to repair, you are better off getting a new appliance.

A good rule of thumb is to avoid repairing an appliance if the cost of repair is half the new unit’s price.

As you are making your decision, remember that most old appliances have fewer electronic widgets, so appliance repair professionals have an easy time repairing them.

While this is the case, there are situations when you shouldn’t even weigh your options and instead replace the appliance. These situations include:

Excessive leaking

A leaking washing machine comes about due to overflowing or a loose connection. If your appliance is old, it most likely uses the same amount of water for every size load. To minimize leaking, determine the load’s size that can fit in the washing machine and leave enough room for spinning, turning, and shaking.

If you do this and the appliance is still leaking, the water hose located at the back of the washing machine might be worn out or has come loose. Take a look at the hose and tighten it.

If you tighten it and the washer still leaks, you might be having a cracked tub. Tubs are expensive to replace, so you are better off buying a new appliance.

The appliance is making a lot of noise.

One of the most common washing machine noises is the appliance sounding as if it’s about to take a flight. If this is the case with your unit, you have nothing to worry about as the unit is simply unbalanced, and all you need to do is rearrange the clothes, so they are evenly distributed.

If the machine makes the noise even when empty, it means it’s sitting on an uneven surface. To fix the problem, position the washer in such a way all four feet are level.

If neither of these solves the problem, your motor mount or drum may need tightening. Contact your local appliance technician and find out how much it will cost you to do it. Depending on the amount charged, you will assess whether it’s wise to repair the unit or get a new one.

The appliance moves around.

A properly installed appliance should stay in place when cleaning, rinsing, and spinning your clothes. If your washing machine moves around that it looks as if it’s walking, you have a problem.

Begin with checking whether it’s level, and if it’s not, level it.

Even if your walking machine is functioning as well as a stationary one, you should know it’s not normal for a machine to move around. One of the issues that can come about is the appliance sloshing water outside the unit and ruining the floors and other parts of the house.

The walking machine also has high chances of pulling itself free of its connections, and it comes to an abrupt stop.

Ask an experienced professional to look into the problem, and if there is no way you can stop the appliance from walking, get a new one.

Water doesn’t fill the drum.

When your drum’s washer isn’t filling up, it means you have a delayed cycle selection, a problem with your hot and cold water faucets, and a kink in your hose. If you check all of the three and see no problem, your unit might be having a complication with the water intake valve or filter, and this needs to be looked at by a professional.

Sometimes the drum might fill with water, but it doesn’t turn as it should. If this is the case, take a look at the lid switch and belts and ensure they are working as well as they should.

Malfunctioning belts are easy to replace, but if the problem is with the lid switch, the washer repair Springfield professional needs to put in some work. Get a few quotes from different contractors and compare them. Is it worth fixing the lid switch issue or getting a new appliance? It’s up to you to make the decision.